Front view of the Keypack anti-crush multihead weigher with stainless steel hoppers

How to Measure Breakage on a Keypack Anti-Crush Weigher

A low crumb rate in a finished bag tells you the snack held up through the line. It cannot show you where the damage occurred. To evaluate a Keypack anti-crush weigher, measure the same product at three points: before it enters the weigher, just after the weigher discharges it, and in finished packs. Include the incoming sample so that crumbs already in the product lot do not get blamed on the machine.

Define what counts as a broken piece

Start with one stock-keeping unit and the defect your customer would notice. For a thin cracker, that might be a broken corner or a layer of fine crumbs at the bottom of the bag. For a puffed snack, a crushed piece may still be too large to pass through a sieve. Decide whether you need a crumb measurement, a visual grade, or both.

Four example products: fresh fruit, ice cubes, thin crackers and peanuts
Examples from Keypack's product gallery. The sieve method below is intended for a dry snack such as thin crackers.

For the crumb measurement, try the sieve on a reference tray of acceptable whole pieces and known fragments. Choose an opening that lets the fines of interest pass while retaining acceptable whole pieces. Record the opening size and units. If thin intact pieces slip through on edge, or if large damaged pieces stay above the screen, add a separate count of visibly broken pieces. Agree on the visual criteria with the quality team and use reference photos to train the person sorting samples.

Set a consistent sample mass, screening time and handling method before the run. Tare the receiving tray and weigh the unscreened sample. Pass it over the sieve with gentle, repeatable motions, then weigh the material that passed through. Avoid using a shaker setting that can fracture the product during the measurement itself. If a repeat sample from the same lot gives a much higher reading after screening, check the method before running the machine comparison.

Set three sampling points on the Keypack line

The Keypack Anti-Crush Multihead Weigher uses divided feeding paths, slide-type feeding hoppers and angled discharge chutes to shorten or soften transfers. Confirm the configuration on the unit being tested, including whether the quoted system includes a collection hopper. Draw the actual product path during setup so that everyone agrees which transfers lie between the three sampling points.

  1. A — Weigher infeed. Collect product immediately upstream of the weigher using an approved sampling point. This establishes how much crumb is already present after upstream transport.
  2. B — Weigher discharge. Sample downstream of the agreed final weigher transfer and before product enters the bagger. Use a supplier-approved collection point that does not add a long drop. Note whether a collection or timing hopper is included in this boundary.
  3. C — Finished packs. Collect packs at a defined point after sealing. Open them carefully over a tray and recover the contents without snapping pieces at the cut. Sample at the same downstream location on every run.

Use only normal operating access and approved collection arrangements. Do not reach into moving equipment or bypass guards. If the discharge point cannot be sampled safely on the running line, have the supplier set up a separate controlled discharge test and report that difference. A discharge sample taken with a different chute or drop height cannot be treated as a direct measurement of the installed transfer.

Record crumb rate and the change between points

Calculate crumb rate (%) = mass passing the sieve ÷ total sample mass before screening × 100. If the three samples are matched to the same stable run, subtract A from B to estimate the change across the weigher and its agreed transfers. Subtract B from C to estimate the change in the downstream segment. Report differences in percentage points.

Illustrative sample log. These numbers demonstrate the calculation and are not Keypack test results.
Sample point Sample mass Fines mass Crumb rate Change from prior point
A. Weigher infeed 500 g 5 g 1.0% Baseline
B. Weigher discharge 500 g 8 g 1.6% +0.6 percentage points
C. Finished packs 500 g 11 g 2.2% +0.6 percentage points

Collect multiple sets across the same stable production window and label them by run, time and product lot. Take the samples in a way that accounts for transit time between points. Avoid selecting only intact pieces or only easy-to-reach packs. Keep startup samples separate so that a brief surge does not get averaged into stable output. If a downstream crumb reading is lower, look for fines left in a chute, product mix differences or sampling variation before drawing a conclusion.

Compare settings at a realistic production rate

Keep the product lot, target fill weight, bag size and test method fixed. Ask the supplier to run an agreed reference recipe and then adjust one variable at a time, such as a feeder setting or an approved discharge timing setting. Wait for the line to stabilize after each change. Record the actual accepted packs per minute and the number of rejects in a fixed test interval. Use a separate calibrated scale or the approved weight verification process to check finished pack weights. A gentler setting must still meet the production and weight requirements set for that SKU.

If fines rise mostly between A and B, follow the product through the feed path, hoppers and discharge chute. Look for stacking, collision or a change in the transfer gap. If fines rise mostly between B and C, investigate the bagger entry, film tube and later handling before changing the weigher recipe. For a wider look at transfer points, see the guide to weighing fragile snacks and the snack food packaging line overview.

Agree on acceptance before the trial

Write down the crumb-rate limit for finished packs, the acceptable increase across the weigher, the fill-weight tolerance and the minimum saleable output. Set those thresholds with your quality and production teams using your own retail specification. Bring samples from a normal lot, the film or bags you intend to run, and a photograph of what an acceptable pack looks like. Ask for the raw A, B and C readings, the settings used and any sampling limitations so you can repeat the comparison during commissioning.

Discuss an anti-crush weigher trial with Keypack on WhatsApp

Related Posts

How to Choose a Bakery Flow Wrapper for Multiple SKUs

Choose a bakery flow wrapper around the products and packs that make your line hardest to run. Start with the tallest item, the widest...
نشر بواسطة Keypack
Nov 20 2026

How Korean Seaweed Snacks Are Packaged: Automated HFFS Guide

Korean seasoned seaweed snacks—internationally recognized as seasoned laver or gim (김)—have evolved from a traditional East Asian staple into a high-demand global snack phenomenon....
نشر بواسطة Keypack
Nov 19 2026

How to Process and Package Dried Mango for Commercial Production

How to Process and Package Dried Mango for Commercial Production Commercial dried mango is one of the fastest-growing segments in the global dehydrated tropical...
نشر بواسطة Keypack
Nov 19 2026

NPK Fertilizer Production and Packaging: 25kg and 50kg Bagging Guide

Modern commercial agriculture in emerging agricultural powerhouses—spanning the breadbaskets of Sub-Saharan Africa, the fertile plains of India, and the Indus Basin of Pakistan—relies heavily...
نشر بواسطة Keypack
Nov 18 2026

Spice Packaging Machine Guide: Automated Powder VFFS Lines

South Asian spice processing hubs—spanning major grinding belts across India and Pakistan—face demanding packaging hurdles. Ground spices like turmeric, fiery red chili, earthy cumin,...
نشر بواسطة Keypack
Nov 17 2026

How to Process and Package Hibiscus Flowers

Dried hibiscus flowers (Hibiscus sabdariffa), commercially recognized as roselle, karkadeh, or zobo, represent one of the fastest-growing botanical exports from primary agricultural hubs in...
نشر بواسطة Keypack
Nov 16 2026

Why Chocolate Bars Use Pillow Packaging

Why Chocolate Bars Use Pillow Packaging Walk through a supermarket confectionery aisle and you will notice a familiar packaging format: a chocolate bar enclosed...
نشر بواسطة Keypack
Nov 15 2026