How to Choose a Bakery Flow Wrapper for Multiple SKUs
Choose a bakery flow wrapper around the products and packs that make your line hardest to run. Start with the tallest item, the widest finished pack, and the product most likely to shift or break on the infeed. Then ask the supplier to run these formats consecutively using your film. A machine can fit every item on paper and still lose time when the operator has to align the next pack, thread a new roll, or sort the first run for seal defects.
The Keypack WS-Series horizontal flow wrapper is a starting point for regular-shaped products such as biscuits, wafers, and bread rolls. The WS-350D and WS-450XD have different film and pack limits, so the choice depends on the range of formats you actually sell and what a changeover requires.
Build a pack specification for each SKU
Measure each product in the orientation it will have on the conveyor. For a biscuit multipack, measure the stack. For a bread roll sold on a tray, measure the filled tray, including its rim and the tallest point of the roll. Sample several pieces from normal production so the trial can account for variation. Record the finished pack width and length separately from the product dimensions.
- Product: Length, width, and height range, units per pack, orientation, and any tray or insert.
- Film: Roll width, material, print repeat or registration mark where applicable, and a sample of the film you intend to buy.
- Finished pack: Desired dimensions, position of graphics and date code, acceptable seal appearance, and a sample pack if available.
- Production: Target saleable packs per minute, typical run size, and which SKUs follow one another on a normal shift.
Check actual roll width against the machine limit. A nominal bag width describes the finished package, while the film must also go around the product and provide material for the longitudinal seal. Product height, width, and film width can therefore constrain the same pack. Ask the supplier to confirm the combination on your sample.
Compare the WS-350D and WS-450XD
The following dimensions are listed on the WS-Series product page. Use them to identify candidate models and bring the closest-fitting SKU to the trial.
| Published parameter | WS-350D | WS-450XD |
|---|---|---|
| Maximum film width | 340 mm | 440 mm |
| Minimum bag length | 90 mm | 150 mm |
| Bag width range | 30–160 mm | 80–200 mm |
| Maximum product height | 60 mm | 80 mm |
If your small biscuit pack needs a finished length under 150 mm, the listed minimum length rules out that format on the WS-450XD as specified. If a tray with a roll exceeds the WS-350D height limit, bring that assembly to a WS-450XD trial. When the shortest pack and the tallest product point to different models, ask the supplier to assess the full SKU matrix. If neither model fits the full range, review the horizontal flow wrapper collection for other configurations to test.
Keypack publishes the two models' speeds in different units. A useful comparison is the number of accepted packs per minute each model produces with your actual product and film. Keep the conditions and acceptance rules the same across the two tests.
Ask which parts and settings change between formats
Ask the supplier to mark each transition on your SKU matrix with three details: which settings the operator changes, which guides or forming parts need adjustment or replacement, and whether the next SKU requires a different film roll. A shorter biscuit pack on the same film may require only a few setting changes. Moving from a narrow biscuit stack to a wide tray can also change how the product is supported and how the film forms around it. Have the operator demonstrate both transitions during the trial.
Include at least one run with your printed film if the pack carries artwork. Check that the seam, end seals, and date code land in the right places after the changeover. Save one accepted pack from each run so that purchasing, production, and quality teams can review the same samples.
Run a realistic three-SKU changeover trial
Ask for a consecutive run that represents a normal bakery schedule. For example, start with a small biscuit pack, move to a delicate wafer multipack, and finish with a bread roll or tray-packed item. If the bakery never packs rolls on that line, substitute its widest, tallest, or most difficult SKU. Bring product and film for each format so the operator can repeat the whole sequence.
Observe the infeed and first accepted packs
Watch how the product arrives at the forming section. Check whether stacks stay aligned, trays sit flat, and soft products retain their shape. After the first run, inspect finished packs for crushed edges, misplaced print, and visible issues at the longitudinal and end seals. Agree on a repeatable seal check with the supplier and document its result for each film and product combination.
Time the work between acceptable packs
Agree on a start and finish before the trial. One practical definition starts at the last accepted pack of the outgoing SKU and ends when the incoming SKU reaches the agreed continuous run of acceptable packs. Record film replacement, settings changes, guide or tooling adjustments, and any checks the operator performs before restarting. Note the number of rejected packs during startup. If a transition requires cleaning under your plant procedure, track that time separately as well as in the total downtime.
Measure saleable output on every format
After the line stabilizes, count accepted packs over the same test interval for each SKU. For instance, 240 accepted packs in six minutes is 40 saleable packs per minute. Record rejects and their causes alongside that figure. The result helps estimate the output of your actual production mix, especially when short orders mean several format changes per shift.
If small batches are common, also consider how the line groups orders that share film and change parts. The guide to multi-SKU and small-batch packaging covers this wider production planning question.
What to send before requesting a quote
Send the supplier a short SKU matrix, photos showing each product in its feed orientation, finished pack samples, and the list of films you use. Include your normal production sequence and how you judge an acceptable pack. Ask for a written recommendation that identifies the proposed WS model, any change parts for individual formats, and a trial report showing accepted output, startup waste, and changeover duration.
A useful trial answers a practical question for every format: can an operator return the line to steady production and make packs that meet your acceptance criteria? Bring the three most demanding formats to that discussion first.